EXTERIOR
INTERIOR
LIGHTS
PERFORMANCE
SUSPENSION
BRAKES
DRIVETRAIN
WHEELS
 Select Your Vehicle

 Select Your Vehicle

Edelbrock EDE Rollin Thunder Camshaft - BBC Hydraulic Roller Cam


Part #: 2261


$555.95 For each
Free Shipping! *to continental U.S. only









Product Details
Fits On:
1972 Chevrolet Camaro, 1971 Chevrolet Camaro, 1977 GMC K25 Suburban, 1976 GMC K25 Suburban, 1978 GMC K25, 1977 GMC K25, 1976 G... See more

Description:
Edelbrock's Rollin' Thunder #2261 is a hydraulic roller cam ground for 396-502 cubic inch Mark IV and Gen V Big Block Chevy engines from 1967-95. It specs out at 236/245 degrees duration and .625 inches/.639 inches lift on a 112-degree lobe separation, targeting strong low-to-mid-range torque from off-idle to 5500 rpm. Pairs well with Performer intake manifolds and suits daily drivers, trucks, vans, and RVs. Requires a high-stall torque converter and stock-ratio rocker arms; not compatible with 1965-66 BBC engines with a grooved rear cam journal.
About Edelbrock
Edelbrock is a legendary performance parts manufacturer. It was founded in 1931 by Vic Edelbrock, and has an incredible history of success throughout the last last century.

Edelbrock has over six locations totaling over 600,000 square feet, all in California. Their research and development capabilities are phenomenal. Perhaps more than any other aftermarket automotive brand in the world, Edelbrock is known to be a name brand you can trust.
FAQs
Q: What do camshafts do? Why buy camshafts?
A: Air travels through your intake manifold into your intake valves and exhaust valves. By upgrading to more aggressive camshafts on both the intake and exhaust side, it will create greater duration and lift. This means the intake and exhaust valves can remain open longer, which allows for more air to move through the cylinder head efficiently. If you're looking to get more horsepower out of your car, aftermarket camshafts are a great option.

Q: How do you install camshafts?
A: Installation should be left to the pros on this one since timing will be involved. If you plan on doing it yourself removal of the upper timing belt cover will need to be done to reveal the cam gears. The valve cover along with the camshafts will need to be removed. Once this is done replace your factory camshafts the aftermarket camshafts and reinstall your cam gears. Make sure when you remove and reinstall the camshafts and cam gears they are at top dead center (TDC). Replace everything as you removed them and re-time your vehicle.

Q: Are camshafts sold individually?
A: Camshafts are sold individually unless otherwise noted in the product description. Single overhead cams (SOHC) utilize one camshaft while dual overhead cam (DOHC) motors utilize two.

Image Description:
A lot of Edelbrock's success can be traced to its early involvement in midget car racing, where many new Edelbrock parts were tested.
Image Description:
Edelbrock has been making engines faster since flatheads were still new technology!

Image Description:
Edelbrock was one of the first companies to use an engine dynamometer to test performance gains. The Clayton dyno was capable of recording up to 200-horsepower.
Image Description:
Edelbrock's first parts catalog was printed just after WWII, in 1946.

Image Description:
Edelbrock's first purpose-built manufacturing facility in 1949.
Image Description:
Edelbrock's giant campus in Torrance, California houses its design, testing, and manufacturing departments.

Image Description:
Founder of Edelbrock, Vic Edelbrock, Sr.
Image Description:
The infamous Ford flathead Edelbrock Slingshot intake manifold. It was the first to bear the Edelbrock name.

Image Description:
The So Cal Special streamliner used Edelbrock parts through the early 1950s.
Image Description:
Vic Edelbrock, Sr., in his '32 Ford highboy roadster, crossing the timing lights at El Mirage.

Image Description:
Vic with his six-carb Ram Log intake manifold.
Image Description:
Vic, Sr., and his successor, Vic Edelbrock, Jr.

Image Description:
Vic's '32 Ford went 112MPH way back in 1939! It may not sound fast by today's standards, but it paved the way for modern hot rodding.




If you live in California, please note this item may be subject to a Proposition 65 warning. Click here to learn more.



Have a question about this product? Click here to email us!




When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Not able to find what you are looking for?

Ride side exhaust camshaft

Engine Camshaft

2013 2014 2015 2016 2017 NISSAN SENTRA ENGINE CAMSHAFTS PAIR 1.8L 3RC0C 3RC0A

MDS Lifters Camshaft Head Gaskets fits 11-15 Dodge Ram Chrysler Jeep 6.4L

LEFT OUTLET Exhaust Camshaft Fit For Mercedes-Benz 2012-2018 A2760505901 New

Click here to view more Camshafts on eBay





Popular Categories
Exhaust Systems
Cold Air Intakes
Headlights
Tail Lights
Body Kits
Hoods
Struts and Shocks
Racing Seats
Chevrolet Bel Air Parts
Gmc C- And K- Series Pick-up Parts
Chevrolet Bel Air Camshafts
Gmc C- And K- Series Pick-up Camshafts
Performance Sitemap






© 1997- Andy's Auto Sport | All Rights Reserved.