So why do you need a transmission temperature gauge? Watch this video to find out! Highlights include:
*At 0:15, we explain the different situations in which you may need a trans temp gauge.
Check out this video where we explain the benefits of performance radiator hoses and show exactly how to install them!
Everything you need to know about hood pins in one video! In this video, we show you:
*At 0:19, we explain why you need hood pins with an aftermarket hood.
*At 1:30, we tell you about the different types of hood pins available.
*At 2:26, we show you the steps necessary to install a set of hood pins on our project Integra.
In this video, we show you a typical installation of aftermarket gauges into a diesel truck. Highlights include:
*At 0:36, we tell you which gauges we chose for our installation, and why.
*At 2:22, we get started with the installation of our gauges, beginning with our exhaust gas temperature gauge sending unit.
*At 3:53, we begin the installation of our transmission temperature gauge sending unit.
*At 4:55, we install our boost gauge sending unit
*At 6:50, we run our sending unit wires inside the cab of the truck so that we can hook up our gauges.
*At 8:50, we show you how to tie your gauge wiring into your fuse block.
At 12:45, we install our GlowShift gauge pod.
*At 14:00, we finally hook up the gauges themselves.
*At 14:42, we turn on our new gauges for the first time!
In this video, we tell you about the gauges that we installed in our project Integra. Highlights include:
*At 0:59, we talk about the specific gauges we chose and why.
*At 1:46, we talk about gauge accessories, such as sandwich adapters for oil lines.
*At 2:36, we begin our gauges installation.
*At 3:25, we install some gauges in our GlowShift gauge bezel.
*At 6:12, we show you how we installed our boost vacuum gauge's sending unit under the hood.
*At 7:12, we install our oil filter sandwich adapter so that we can get an accurate oil pressure and temperature reading.
*At 10:10, we install our water temperature sending unit.
*At 15:20, we show you the results of our efforts - a slew of new performance gauges!
Heatshield Products keep your engine compartment safe, and can even help protect your vehicle's finish. In this video, we show you how installing a heat shield on your hood can prolong its life and new appearance.
*At 0:42, we get right to installing a Heatshield Products Lava Shield on our project Integra's hood.
*At 2:02, we show you how much cooler our hood's surface is after installing our heat shield.
In this video, we go over the ins and outs of aftermarket gauges. Highlights include:
*At 0:38, we explain why aftermarket gauges are usually more accurate, and therefore more useful, than factory gauges.
*At 0:48, we talk about air/fuel ratio gauges.
*At 2:14, we talk about boost gauges.
*At 2:30, we tell you about boost vacuum gauges.
*At 2:42, we go over fuel pressure gauges.
*At 2:56, we talk about oil pressure gauges.
*At 3:07, we talkabout oil temperature gauges.
*At 3:28, we tell you about water temperature gauges.
*At 3:40, we talk about tachometers.
*At 4:02, we talk about voltmeters and amp gauges.
*At 4:28, we go over exhaust gas temperature gauges.
*At 4:44, we offer our opinion of the most critical gauges to get for your vehicle.
*At 5:08, we tell you about the different types, styles and sizes of gauges available, including mechanical, electric, analog, and digital.
Headers - Presented by Andy's Auto Sport:
Check out this episode of Andy's Auto Sport TV where we explain all the basics about headers. In the video, we explain why headers open up horsepower gains and explain the difference between different types of headers. We also show how to install headers and then show the resulting horsepower gains with our dyno run results!
Shift Boots - Presented by Andy's Auto Sport:
If it's time to replace your shift boot, you'll want to see this video. In this episode of Andy's Auto Sport TV, we install Redline shift boots and a transfer case boot on our project Jeep Wrangler, Acura Integra, and Honda Civic. See how easy it is to update your interior in almost no time at all! Video highlights include:
*At 1:07, we show you how to install a shift/transfer case boot on a Jeep Wrangler.
*At 1:48, we install a shift boot on a Honda Civic.
*At 2:31, it's the Integra's turn, as it gets a carbon fiber style shift boot to match our carbon fiber style seats.
Mass Air Flow Sensors - Presented by Andy's Auto Sport:
On this episode of Andy's Auto Sport TV, we explain all the basics about mass air flow sensors and what you need to know about them!
Pedals - Presented by Andy's Auto Sport:
In this Andy's Auto Sport Short, you'll learn how easy it is to install a set of aftermarket pedals, which can help improve your driving and add some style to your cabin. Video highlights include:
*At 0:16, we talk about why you may want to replace your factory rubber pedal covers.
*At 0:36, we show you how to shop for pedals on AndysAutoSport.com.
*At 0:44, we show you how aftermarket pedals are installed.
*At 1:47, we compare our boring stock pedals with our new NRG pedals.